xpfguy

Members
  • Content Count

    274
  • Joined

  • Last visited

  • Days Won

    2

Everything posted by xpfguy

  1. ok… I know there are Mac users but this section seems to have very few post. So I wonder, are there lots of people using Mac and not having any problems or are there just not that many using a Mac? Please humor me respond if you see this, just list basic setup. Ill start right after I post this.
  2. xpfguy

    ok font master, help need

    is this full custom or a actual font?
  3. xpfguy

    ok font master, help need

    Findmyfont $49... I'm sold!! thanks
  4. xpfguy

    ok font master, help need

    Yes that worked with a little tweak on the T. on my coreldraw under Text options there is a selection for Whatthefont?! but it not highlighted select-able?
  5. xpfguy

    Font help

    I just searched and I can't find this... help please
  6. xpfguy

    Font help

    Dang that was good... I guess when you don't have them they are harder to find.
  7. xpfguy

    Font help

    Dang that was good... I guess when you don't have them they are harder to find.
  8. xpfguy

    my sublimation review

    Dusty from sitting around waiting for the printer fairy to come fix it, she never showed up.
  9. xpfguy

    my sublimation review

    https://www.youtube.com/watch?v=8AVtPgTEF08 I guess it's my fault for not doing some investigation before spending hard earned money.
  10. xpfguy

    Are there any Mac users out there?

    I use a 08 MacbookPro and an even older mini with CS5 and never noticed and lagging other than tracing a large multicolor design. I also upgraded both to SSD hard drives and could not be happier. Recently i've been using Microsoft Surface Pro to do everything. It's an amazing tablet... CS5, Corel Draw, iDesignR all work flawless. Jason
  11. wheel accents wrapped with orange oralite the circuit board is black reflective (white reflective at night) almost invisible in daytime.
  12. xpfguy

    font master, i need you

    I made this a few years ago and now can not find the font. saved all versions with type create outline. I will not do that going forward. probably an easy one but i can't find it.
  13. xpfguy

    New etching for my shop

    very cool
  14. xpfguy

    MESSING AROUND

    looks nice. might try to make the boat with outlines. reason is when someone wears a shirt like that or similar with a large solid piece of heat transfer it becomes a hot spot on the shirt. no air flow and tends to make a stick sweaty spot. HTV is great but not for doing large solid designs, try to outline. my 2 pennies
  15. xpfguy

    Needing Help.. Yet AGAIN!

    I was going to suggest make sure you blade holder did not come loose… that happen to me one Also making sure your pinch rollers are clean. both of these would cause some poor cuts.. or worse
  16. oh.. and a real sharp new blade one class I took, we were told on certain material you may need to snap the blade off about every 6 feet to maintain a clean cut.
  17. not sure about this, but if you pulled a piece of knifeless from side to side (the 84" width) and made sure its level you would have a nice straight clean cut across the top of the vinyl. as for as the other sides, like kal259 said except no need to hinge. just take a piece of vinyl about 12" x 90" and slap is up wet.
  18. xpfguy

    Latest Mirrors

    great work
  19. xpfguy

    Are there any Mac users out there?

    Macbook Pro 10.7.5 , Graphtec CE5000-60, Illustrator CS5, CM3 recently installed Graphtec Studio, but have no opinion yet.
  20. xpfguy

    Applying cut vinyl to hard hat

    solve your problem… use vinyl with an air release adhesive: Hexis all there HX products have this. 3M has Controltac to name a few that way if you handing them out you don't need to give heating instructions :-)
  21. Having problems installing Graphtec cutter, make sure you are not plugging it into a USB 3 (blue) port. After hours of frustration, it simply came down to switching it to the USB 2.0 port. story goes I had a computer go down and had a few RUSH jobs to do, so I grabbed my laptop and proceeded to install my cutter. I mistakenly was plugging it into the blue usb and the computer insisted i was installing a printer with problems.
  22. Just a follow up, even after a proper install now the Plotter is not recognized through USB 3.0 That really stinks because I was thinking of setting up my Surface Pro to run it as back but it only has USB 3.0 Come on Graphtec, if your aware of this please fix. Maybe there is a firmware upgrade. I will let you know if I come across one.
  23. xpfguy

    Reflective Vinyl tips needed

    I have basically the same setup. I have cut a lot of reflective… the jeep with the digital circuit board for one if you have seen it. When I get a chance I will post my exact setting and how i set my blade. I have never heard of the credit card thing. I'm self taught so I may be doing it wrong but I've had no problems. Also, my blades last a long time..
  24. xpfguy

    Heat Press (able) Lanyards?

    You should have no problems. There is heat transfer material made for nylon. I recently did some camera straps, poly though. Try Thermo Flex Xtra