after factory reset, doesnt work !!!!

[after factory reset, doesnt work !!!!]

hi

originally it showed  "Novram Init "

 

thanks

[after factory reset, doesnt work !!!!]

hi
done factory resetting , but once power on , some weird things show on the screen , as below

it is supposed to be 1st photo ,

any idea why?

it may be cable problem? slightly damaged when it was pulled off.

where i can this cable?

thank

[what is Novram Init ?]

the photo is attaced.

cant control any. , im using signblazer

 

have to change motherboard?  it it is  replaced, what is need to set? 

 

 

can you take a picture of your cutter screen and post it with that on it?

 

Can you do anything on your cutter?    Change any controls at all.?  And what cutting software are you using?

 

Make sure you are using the correct command for Graphtec software.  GP-GL     and any other cutting software other than a Graphtec language would be HP-GL.

 

And you are Holding down the up arrow at the same time you are tuning on the power, correct?

 

[what is Novram Init ?]

hi

when i turned on the cutter, Novram Init message showed then , the cutter didnt move at all, even couldnt load ,

tried factory setting - hold up arrow key and power on , but nothing changed.

anyone knows why and how i can sort it out?

thanks

[how to divide the photo and change resolution to print?]

hi 

i have roland rs 640 and versa works 

 

will print on oracle 3268 vinyl

 

 

thanks 

[how to divide the photo and change resolution to print?]

hi 

 

i will print wall paper covering around 2x3 M as its size , will divide 3 or 4 section , overlapping 1 cm 

the photo size is 

 

30 cmx28 cm (300dpi) 34.5 MB

 

how to cut into 3 or 4 sections and change size and resolution in photoshop?

 

thanks  

[any one know what material ?]

hi

the photo is attached

[any one know what material ?]

hi

as showing on the photo.

http://cafeptthumb3....y.jpg?type=w740

it is very thin plastic sheet ,

how do you call it and when we can get it?

i guess it cut by Silhouette Cameo.

can it be cut by normal cutter like ce-5000?

thanks

[why i cant merge ?]

hi

anyone know how to do in AI ?

thanks

[why i cant merge ?]

hi

thanks for answer..

but can you explain how to weld?

i tried to expand , but cant press the expand button in pathfinder.

thanks

[why i cant merge ?]

hi

i cant merge with the butterfly body with other part.

how i can make one object?

any idea?

thanks

butterfly body.eps

[contour cut and signmaster 2 cutting error?]

hi

plz see the photo,

the cutting is not correct position ,

set reg mark in signmaster 2 and send to graphtec cutter

what went wrong?

printer problem or cutter settling wrong?

whole graphic size is 60* 20 cm ,,

any idea?

thanks

[can the signblazer run many cutters?]

hi

thanks for answer ,

i manged to cut 2 cutters with one pc,

but whenever cutting a new, do i need to change output device setting?

for example.

open a 2 sign blazer, then one is usb 1 output setting in signblazer , the other is usb2 output setting in signblazer ,

after cutting finish, usb1 always change into usb2., so have to change back to usb 1 when cutting a new one,

how i can solve? how i can fix the usb out ?

thanks

[can the signblazer run many cutters?]

hi

i have few cutters with each pc to run.

can one signblazer in one pc run many cutters?

if yes, how to do ?

any advice welcome

thanks

[all mixed path line?]

thanks for replying

i have PCUT CREATION.

[all mixed path line?]

hi

as u can see the photo,

when i cut the image file, the knife goes everywhere.

not follows the path.

similar things have happened in Artcut,never in Signblazer.

any idea?  

Untitled-1.eps

Untitled-1.eps

[CANT CUT SIMPLE SQUARE!!]

hi

im usuing a pcut creation

[CANT CUT SIMPLE SQUARE!!]

HI

as shown the photos, one corner in square is not clean.

i have chaged the offset from 0-7.0

square size is 5*5cm

all same results... any idea why?

[when importing the letters?]

thanks again,

i just realized even when i type the word in sign cut,

it cut 2 times.

well , setting problem?

[when importing the letters?]

thanks

as showing the photos, i try to drag the letters, but i cant

did i miss the point what u said?

or

i have to do in the illustratior?

[when importing the letters?]

thanks for reply

can u tell more ?

how i can delet the layer?

[when importing the letters?]

hi

after outline the letters in illustrator, importing then cutting

but it cuts 2 times , it cuts and cuts again folllowing first line exactly

any idea? why?

 

[when the path is not correct?]

hi

the path was fine in illustrator cs2 (photo bottom one)

but

when importing the artcut, it was not correct (photo upper one)

anyidea why and how can i correct?

[EDGE CUTTING]

hi

offset from 2.5-4.0

it looks like the photos

what is the problem?

if offset is worng, it looks like this? or blade depth is wrong?

help!!!

[size?]

hi

i set like the photos

every unit is cm

but actual cutting is converted into inch

setting is 3cm*4cm

but actual cutting is 3 inch * 4 inch.

how i can change the setting?