bruceking66

Well, I guess the verdict is in. This machine SUCKS for the detail I am looking for. Which, I didn't think was that much. Sad to say, that my previous LIL GAY cutter was BETTER than this one. It cut perfect circles EVERYTIME, there seems to be nothing else I can do.!! Hard to believe, that I bought this, HOPING for the same results as a inferior machine but with slightly more downgrade pressure!!! All, yes ALL of my other templates made by gay lil Klic N Kut are FAR SUPERIOR to what I have now. Thats, just unbelieveably ridiculous! I wasted my MONEY! **** all this OFFSet, Ihave tried it ALL! eXCUSE ME FOR THE NEGATIVE ATTITUDE, but FACTS IS FACTS! I appreciate all the help, But it doesn't seem to matter. I'm just so disappointed that this machine, IS inferior to a KNK machine!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! I sold that KNK machine, so I am stuck with this piece of CRAP! EDIT BY FIVESTAR I know you're upset but please try to watch the language.

Ken, I really appreciate the response. And You did call me at my first post to help. But, seriously, if the pen can't draw it right, what difference would the blade make? I will say, the community here has been great. Personally, I don't think there is a problem! I don't think this machine can handle this SMALL amount of detail I , mean look at the thread........... can anyone tell me what I haven't tried??? I'm in the between HERE.... I want to keep going... But, I have seen ZERO progress from ALL suggestions, although I have APPRECIATED ALL.... Which leads me to believe, its just that the machine CANT handle IT! I will say this, My main purpose is to make templates for rhinestone patterns.... Disappointed that a lil GAY Klic N Kut machine DID a WAAAAAAAAAAYY better JOB of that. However, I usually have to make the template circles or pattern slightly larger than the original. So that they lift off without gettig stuck. I do this so that there is a little room to have the transfer tape pick them up without getting stuck! I Dunno if you guys get my drift, but, I can LIVE with IT, BUT I DON:T LIKE IT!!!!!!!! MY KNK GaY MACHINE WAS RIGHT ON THE money....IT WAS JUST WEAK AS FAR AS DOWNWARD PRESSURE. And having t weed as al. I did make circles from 1 mm all the way to 30 mm. And, tried dozens of OFFSETS... there really wans't much change at ALL! I stuck with around .02 mm, and paid alot of attention to my blade depth. Its still not RIGHT! Also adjusted the tension on the drive belt screw, I DID NOT SEE ayway to adjust the rollers for the feed rollers?????? I just don't think this machine is up to the task of cutting that small..........VERY DISSAPOINTED!!!!!!!!!!

CORNHOLE

Ok, first of all I want to thank you and everyone for attempting to help me..... I did the above test on both ends and it measures fine both ways on both ends... What could it be now?

I'M using SignBlazer, I don't see a setting for Overcut?

Wish my problem was that simple. My carriage is fine....http://forum.uscutter.com/index.php/topic,14904.0.html I am using my cutter to cut small circles for Rhinestone templates. The smallest being 2mm circle. Very inconsistent, I used to have a little Klic N Kut machine it cut them perfectly everytime, Regret supposedly upgrading...Any help, or is just the fact this mcahine can't do that small of detail.

Notice how on the bottom side of this cupcake image the circles are larger than the candle on the top. They are all the same size in the original image.

A 6 inch circle, measures perfect! So, yea You are right, But, how do I get it dialed in?

THe larger ones do look better, but I measure and they are still off a little. Its just harder to tell on the big ones. But, the small ones, you can easily tell. Posting pic...

No amount of OFFSET makes any difference what so ever....also tried at all speeds...

Yes, hey good to check everything! I put in my pen plotter and drew a box, measures EXACTLY right! Then I make circles with the pen, they are NOT round? I'm stuck Any other ideas???

While I'm at it, its not the Blade either...been there, done that...

I have the US Cutter MH-871. I adjusted the horizontal belt, but didnt pay much attention to the small belt I assume was for the rollers. I'll have to open her back up tomorrow and see if there is adjustment screw there as well. (Too late tonite, everyone asleep already) I will defintely look a little closer at the Axis thing and get my plotting pen out. However, on previous test cuts, Squares seemed to be on the money. Just these GD circles...Circles are my LIFE. By the way, here is what I do with them.. www.CharmedOneDesigns.com Be back on tomorrow, thanks for all the replies...Bruce

I was sure to make some different sized circles in SignBlazer and imported for Corel...No Difference....SignBlazer circles are just as bad. So, definitely not the design being imported...

I went for it and made some adjustments, tighter and looser....several test cuts.....NO change...Anything else I can try?