mobby
Members-
Content Count
85 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Everything posted by mobby
-
Upgrade available for win 7 32 & 64 bit
-
The "cracked" version is 6.05. The final release version was 6.0.27. The 6.05 is bug ridden. Try some complex node editing and suddenly a mass of lines appear. Also scaling is wrong for most chinese cutters. This is because the chinese think that there is only 25mm in an inch, so cutting a 500 x 500 square you get 508 x 508. The drawing tools randomly fail due to a failed license check. There is two license checks, and the crack only addresses one of them. The other one is random, so difficult to remove or bypass. As for removing the dongle, good luck, as part of the software runs in the dongle. Cheers Mobby
-
Jerry did not write the code. A few good ideas died with him but not much elese. look to the relaunch of elements soon
-
a few copies of Pro & Hotshot are still available
-
PLEASE READ BEFORE POSTING!
mobby replied to marcuso's topic in USCutter Refine Cutting Plotter Support Requests
Very common for the screws holding the solenoid and magnet concentric move slightly and cause coil, and hence head to rub and jam down. Cheers mobby -
Windows VISTA USB setup for Refine plotters
mobby replied to MarcelC's topic in USCutter Refine Cutting Plotter Support Requests
See my other post same port speed problem Cheers Mobby -
MH721 and SIGNBLAZER I have had enough
mobby replied to signqueen's topic in USCutter Refine Cutting Plotter Support Requests
This is a common problem. I think it is caused by the com port speed of computers being too quick for the low quality electronics used in most chinese cutters. You need to slow the port down in device manager to fix this. I recently fixed a CE1000 graphtec that was cutting garbage on a Vista laptop, to cutiing reliably. Most of the Cinese USB cutters dont have proper USB ports, just an on board USB - serial chip. Try it, it might fix the problem. mobby -
Signblazer, the name is gone forever. However replacement products are just around the corner. Mobby
-
Not sure what you are doing here. You are in the print menu. Why are you not in the cut menu
-
SignBlazer Elements Activation Code not accepted - Help Please
mobby replied to SBSAUS's topic in SignBlazer
If you are in Australia contact mike mobby@tpg.com.au -
Note Edit Points Have Disappeard. Only appear When High Lighted.
mobby replied to ElementOfDeath's topic in SignBlazer
When you are node edditing, click on a color in the palette and fllow instructions -
Send Mike an email at mobby@tpg.com.au
-
The array tool is available using "Y" as a shortcut. It is also halfway down the "Edit" menu
-
Just a warning here. For mainstream cutters like Roland, Graphtec etc, offset needs to be 0.00, as the cutter itself provides the offset setting. Some Chinese cutters will soon be the same, so be vigilant. Always use cutter offset rather than in software. mobby
-
The clockwise & counterclockwise is not relevant for vinyl cutting. It is used to control the loop directions for dxf & eps files sent to routers that don't have their own software to reorder the cutting paths. For routing, the inside loop has to be in the opposite directin to outside loop. This is to ensure that the burr is always on one side ie the backside of the sign. Used in conjunction with "cut holes first" it also ensures that insides are cut first, as they must be for routing. It is also an advantage if you a cutting small letters, because if the outside is cut first, the shape make come loose from the sheet when the inside is cut. An example would be the letter "O" mobby
-
You can also create your background color and then go to edit & lock the object Cheers Mobby
-
Signblazer does not read 2 byte fonts, as are required to display asian charactors
-
Could be a communication problem. Also long jobs can cause this as well. Not many of the 24" Chinese cutters can cope with files longer than 2 metres, and 3 meters max for stability. I need more info, and the file to help further. mobby
-
Just load windows on the MAC, and Signblazer will run OK, and cut through the USB ports. mobby
-
absolutely mobby
-
When you are in node edit, press F1, and help file will appear mobby
-
You can use the array tool to put them on a circle or arc, but not follow path mobby
-
Just select all and the "P" for punch mobby extremebedside5punch.SBD extremebedside5punch.SBD
-
Try this to create bridge mobby
-
Refine MH721 is same as ProCut mobby