TeslaCoiled
-
Content Count
7 -
Joined
-
Last visited
Posts posted by TeslaCoiled
-
-
Be "nice" if the driver sw reference (mentioned on a few postings)
referred to a "pinned" or sticky posting.
I'm about to try:
http://start.uscutter.com/laserpoint/cutter/driver
from http://start.uscutter.com/laserpoint
from https://support.uscutter.com/hc/en-us
If this gives me headaches, I'm moving to Linux;
http://libregraphicsworld.org/blog/entry/vinyl-cutting-on-linux-the-real-deal
https://www.google.com/search?site=&source=hp&q=linux+vinyl+cutter+software -
Be "nice" if the driver sw reference (mentioned on a few postings)
referred to a "pinned" or sticky posting.
I'm about to try:
http://start.uscutter.com/laserpoint/cutter/driver
from http://start.uscutter.com/laserpoint
from https://support.uscutter.com/hc/en-us
If this gives me headaches, I'm moving to Linux;
http://libregraphicsworld.org/blog/entry/vinyl-cutting-on-linux-the-real-deal
https://www.google.com/search?site=&source=hp&q=linux+vinyl+cutter+software
-
Be "nice" if the driver sw reference (mentioned on a few postings)
referred to a "pinned" or sticky posting.
I'm about to try:
http://start.uscutter.com/laserpoint/cutter/driver
from http://start.uscutter.com/laserpoint
from http://start.uscutter.com/
If this gives me headaches, I'm moving to Linux;
http://libregraphicsworld.org/blog/entry/vinyl-cutting-on-linux-the-real-deal
https://www.google.com/search?site=&source=hp&q=linux+vinyl+cutter+software
-
Be "nice" if the driver sw reference (mentioned on a few postings)
referred to a "pinned" or sticky posting.
I'm about to try:
http://start.uscutter.com/laserpoint/cutter/driver
from http://start.uscutter.com/laserpoint
from http://start.uscutter.com/
If this gives me headaches, I'm moving to Linux;
http://libregraphicsworld.org/blog/entry/vinyl-cutting-on-linux-the-real-deal
https://www.google.com/search?site=&source=hp&q=linux+vinyl+cutter+software
-
Be "nice" if the driver sw reference (mentioned on a few postings)
referred to a "pinned" or sticky posting.
I'm about to try:
http://start.uscutter.com/laserpoint/cutter/driver
from http://start.uscutter.com/laserpoint
from http://start.uscutter.com/
If this gives me headaches, I'm moving to Linux;
http://libregraphicsworld.org/blog/entry/vinyl-cutting-on-linux-the-real-deal
https://www.google.com/search?site=&source=hp&q=linux+vinyl+cutter+software
-
0. I've been enjoying using my LaserPoint 48" Vinyl Cutter on & off for the last 3 yrs,
but I distinctly see needing some digital ink printed vinyl, esp for partial car wraps.
1. What is the best price anyone's seen for printed vinyl (& laminated) (that you can use for wraps)?
I can always get a good image to use & enlarge it with minimal pixelization from umpteen family jackets, home made blinds etc., so...
2. What is the best price anyone's seen for pre-printed camo (car wrap)?
The best price I've seen for mossy oak camouflage is $4.125 per sq ft
on a Sheet Size: 2 feet x 4 feet (8 sq ft) ($33/ 8 ) .
http://www.powerspor...ps/503/infinity
price est chart by vehicles http://www.powerspor....com//chart.php
3. Any advice/ heads-up's I should know of (like air channels, etc)?
Thanks kindly!
-
1
-
Write Port Error
in Flexi
Posted
The flexi drivers work like a dream! (see a few postings above)
What led up to the post was a ton of headaches;
The posts I looked at, led off to dead ends for what was needed to get running.
People saying I fixed my problem, then not saying how they did so.
I was looking to cut a 10' baner w/ a LP48 I'd had in mothballs for over 1 yr,
on-site, where I thought it'd be fun to let the client see the job run
(& the avg. Joe walking by- I esp. love to watch kids' reations!)
The guy's a US vet, 30 yrs in the Service, just left Afganistan & is runing for a Governor's post.
Flexi had crashed spectuacularly on the old PC, so....
I started w/ SignBlazer, but every test job was running in odd directions, mirroring, w/o (&w! ) fields being checked.
Corel.. wanted MS net 3.5 to reinstall- oh,no 4 wasn't good enough, (even had the 4 full install on the drive)
& I was on a public site w/o wireless....
Reinstallled flexi & was looking for the drivers- it'd been 4+ yrs since I'd done the install.
I was besieged w/ enough headaches
& wanted to post someting to make the next Joe's life easier.
Amazing how a few whinners are like 1 rotten apple ruining the whole barrel.
Crossposting should be an easier option, if the aforementioned need binki's.
& the links provided are to FREE Linux vinyl-cutting programs that weren't around or nowhere near mature enough to use 4+ yrs ago. I encourage any geek to try out Linux Mint 11 or 15 (mate versions). Drop in a DVD for a live test, w/o having to install.
Per Google's mantra... Don't Be Evil.