lizzylou
Members-
Content Count
76 -
Joined
-
Last visited
-
Slice has posted the link so many times. and just recently. Jump thru some of his posts.
-
Cuts not lining up...
lizzylou replied to AmericanWarriorDecals's topic in TITAN 2 Series Vinyl Cutter Discussions
They are referring to tightening the set screw inside the steel grit rollers on the bottom,,Not the pinch rollers above. With the cutter off, turn the steel grit rollers on the bottom by hand, until you can see the set screw in it, and make sure they are tight. It is not advisable to start messing with the tension on the pinch rollers above, you will just create more problems for yourself. Glad your getting the blade depth tuned in.. For Offset start at 0.25mm and adjust at small increments. If it starts looking bad 1 way plus or minus, then go the other way.until corners are sharp. -
Cuts not lining up...
lizzylou replied to AmericanWarriorDecals's topic in TITAN 2 Series Vinyl Cutter Discussions
Instructions never say have the blade depth out a credit card depth or even 1/2 credit card.is a myth that will not go away. You really need to change your blade depth to the correct depth...A credit card thickness is very incorrect..The blade depth instructions have been posted a lot on here.. You have bad cuts... You are here asking for advice. Put the blade depth where it belongs, and use the force of your machine to cut the depth. With the blade being out that far you are not cutting with the very tip of the blade as you should be...You should only see and feel the blade tip out of the blade holder.. You are creating your own problems, by not having the blade set correctly. That is the first thing you should do when you set your cutter up. From 1of MzSkeeter's posts on how to set the blade depth correctly. It works perfect. "This is how to set your blade depth correctly.. You should barely see or feel the blade out of the blade holder. To start with, you should set your blade depth correctly, by taking the blade holder out of the machine, and firmly cut across a piece of scrap vinyl, you will be cutting. You should only be cutting the vinyl and barely a mark on wax paper backing, Adjust blade to get there, Then put the blade holder back in machine, and use the force of the machine to get there, same results, only cutting the vinyl and barely a mark in wax paper backing." -
Instructions for TC vinyl cutter serial connection contour cutting, using software to interact
-
For a TC series cutter if you are using USB, you cannot control the setup of contour cutting from the software.(Scalp). Listen to the instructions..Only manual on the machine,then enter the numbers manually into the cutting software. They are showing Flexi software, but I would think Scalp would be the same way.You do not state how you are doing it. USB or serial connection.? Here is a video for contour cutting with a TC cutter with USB set up. There are more videos on youtube for contour cutting with a TC cutter.
-
Makes more sense... Thanks for the verification...
-
us cutter ts series ? Which cutter is that? I have never seen a ts series cutter ever sold on UScutter.
-
never heard of a ts series cutter, Which model is that? and welcome
-
Awesome work...
-
Just got a new MH871-MK2 and it won't communicate with Windows 8.1
lizzylou replied to Trampsinger's topic in LaserPoint Cutting Plotter Support Requests
Follow instructions here, http://www.uscuttersupport.com/mh-series-vinyl-cutter-setup.html -
CE5000-60 Looking for part
lizzylou replied to Carlos Sanunga's topic in GraphTec Cutting Plotter Discussion
Are other cable brands the same? -
Are there instructions on the cutting controller? Looks like HELP at the right top.
-
this? http://www.hobbylobby.com/Art-Supplies/Canvas-Surfaces/Poster-Board/22%22-x-28%22---1-Sheet-Pacon-Dry-Erase-Poster-Board/p/7138
-
your welcome, that LP cutter is a Liyu brand