espy

Members
  • Content Count

    37
  • Joined

  • Last visited

    Never

Community Reputation

0 Neutral

About espy

  • Rank
    Advanced Member
  • Birthday 01/01/1

Profile Information

  • Gender
    Not Telling
  1. Yes, I need to send the old one back for a refund. I spoke with you on the phone and you said I didn't need an RMA, but I do need to get instructions, i.e. the address to send it to, and any thing else I need to include with it so that credit is applied to the right account.
  2. Anyone know how to set up the rulers to feed the vinyl through straight? I've been using a copam 2500 (and have loved it), but had to send the original back due to warranty issue. The new cutter is working great except that the rulers are off. That is, the blue ruler on the bottoms marks don't correspond with the top ruler marks...which makes it hard to line the vinyl up correctlly so it doesn't track to the left or right as it feeds through. I think that the top ruler is removable and can be repositioned, but I've tried to get some straight consistent marks, and haven't found a way to do it. Anyone have any tips or tricks for me. I need to get the rulers exact as possible, because even being off slightly causes the vinyl to track to the left or right when cutting longer jobs. Any tips or advice would be appreciated.
  3. Did you do a system restore....sounds like something might have gotten messed up in settings, or buffer.
  4. SOLUTION!!! I got my new copam 2500 here today, and just as I suspected...it was a cutter issue! the new cutter cuts perfectly using the Graphtec CE1000-60 driver in Flexi. Set it up via serial to usb, with a USB extention cable (since usb cable provided is only 3 ft long). Working great...after all of that pulling my hair out...no wonder I couldn't figure it out....hardware problem!
  5. I tried the PNC-960 and HPGL drivers, stuff comes out all garbled, and just cuts random stuff....so doesn't work at all. It seems to be tracking just fine. Also, I tried changing the offset in both the software, along with changing it on the cutter, neither fixed the problem. The best results are with .20mm offset set in the software, with the cutter offset left at standard (.25mm). But still doesn't complete the cuts. Also, even in signcut, it's not completing cuts...mostly on weeding lines, but I'm noticing the same gaps (about 1/8 inch), so I'm thinking it's something with the cutter itself. Also, the simple fact that I've been using the cutter with the Graphtec driver with NO PROBLEMS for almost 10 months leads me to believe that it's something with the cutter.
  6. Nevermind that last post....even in signcut, isn't completing the cuts, just not completing them in different places....which is why I didn't notice until now. Also, signcut doesn't have a "weld" feature I can find, so when cutting cursive, the letters get all chopped up....
  7. espy

    Weld Feature in Signcut X2?

    Has anyone noticed how in signcut if letters overlap, signcut doesn't weld them, but cuts through them....anyone know how to weld the letters together in signcut? I'm using illustrator, don't think I can do it there.
  8. It seems to be completing the cuts just fine using signcut X2 (which doesn't allow any design functionality). I use flexi for the design functionality it provides. I've played with the offset, and changed settings on a range from .01mm to .60mm....and it still doesn't complete the cut. Its hard as well because I'm using a graphtec driver that comes standard in flexi, and it has worked flawlessly for the past 9 months until just recently....so I'm not sure what could have changed. I talked to flexi, and they provided a csm file for the copam, but the file doesn't have the option for LPT1 printer port, only com port, and I couldn't get teh copam to work hooked to the com port of my computer. So, I think it's a software issue...too bad the copam can't figure out how to provide a descent driver that works with the industry leading design software....Flexi!
  9. I looked at that, doesn't appear to be anything loose at all. I tried several new blades, I even tried a different blade holder, still no change. I'm really at a loss here.....any ideas? It's leaving big gaps where it's just not completing the cuts as it should. about 1/8 to 1/4 in gaps, which makes weeding damn near impossible.
  10. I have put two different blades in (both roland blades, .25mm offset, and I've played with the offset settings in both the software, and on the copam iteself...neither way produces any results...in fact, changing the offset in the software does nothing, neither does changing the offset on the cutter......it doesn't appear to change anything at all! What is going on.....I have some big jobs to cut, and my cutter is acting up. I've been using this for 9+ months without problems, and now all of the sudden it started acting up, no changes to software, no changes to blade type, etc....what could cause this....I wonder if it's the blade holder not allowing it to swivel or something. I've cleaned the blade holder, even put a little oil on the swivel end of the blade....still no change. any ideas?
  11. I tried .10, .15, .20, .25, .30.... still doesn't complete the cuts.....this just started...it was cutting fine with .25mm offset on both the machine and set in the software. I haven't changed anything...even checked the font using a font that I cut all the time with no problems. This just started today.....and I'm at a loss for what to do.... Any suggestions?
  12. I can try that...but not sure why it would all of the sudden not complete cuts when it's been working fine for months.......I haven't changed any of the settings....
  13. My copam just started having issues completing cuts. I've used it for months without a problem, but now for some reason it's not completing cuts....so makes weeding near impossible. Any ideas of what would cause it to all of the sudden not work...I changed the blade thinking a dull blade might be to blame, checked offset (.25mm). What perplexes me is that the problem just started......never had an issue before now. Any ideas?
  14. My copam 2500 has been working great with Flexi using the Graphtec driver I mentioned in a previous post, however it recently started doing some strange stuff. Sometimes when cutting a job, the cutter will make a friction-like grinding sound, and when it does it does not advance the vinyl, however the cutter head thinks that the vinyl has been advanced, and therefore throws the cutting off....and cuts over items that have already been cut. I noticed that this primarily happens when the cutter goes to feed more vinyl off of the roll...as if the pinch rollers were strong enough to roll the vinyl off...so it grinds, or skips..etc. I Checked the rollers, and they are for the most part friction free, and very free-rolling...so I can't imagine why the cutter would be doing this..but I've messed up a couple of big jobs becase of this....and I need to get it fixed. marcel...can you please call me regarding this...I think that there may be something wrong mechanically with the cutter I have...because it all of the sudden started doing this, and it seems as if the rollers just don't have enough strength to feed vinyl from the roll....which is a huge problem when you're cutting a large job. I really love this cutter for the most part, but I just need to figure this one aspect out..and since I've only had it for a couple of months, it should still be under warranty.