Archer

h1p1n3 Glad you got it up and running

Back in business ran some test cuts and all is good

WoooooHooooooo I got the VinylMaster pro to work I need to do some test cuts but it appeared to go threw the motions of my last lettering job correctly without a knife in it. I started loading different drivers into it and the USCUTTER SC - 25 in seems to work. So as it stands right now both SB and VM are working. I can't thank everyone enough for all the help. I am going to load some vinyl and give it back its knife and see if it behaves

Ok so some progress I loaded SigneBlazer back on the tower computer and used the Red sail RS 360C driver as MZ SKEETER suggested and it works I need to make some test cuts to make sure but the cutter did come to life. Now I'm going to try to use some other drivers with VM We're Getting closer.

Slice. Whether it gets me up and running or not I greatly appreciate all the help from everyone. Also something new, not only am i getting the device not recognized with the yellow triangle I an getting another usb listing It says USB Serial converter and that it's working properly The one not recognized is on Port_#0004.Hub_#0003 and the one working is on Port_#0002.Hub_#0003 but still no luck on bringing the cutter to life. I am going to un install VM and re-install but before I do I will shut down the USB security thing and see if that makes a difference

Ok ill try that tonight. I would like to get something to work on the tower so I could figure out if it's a hardware or software problem. Lucky for me the jobs I took on were just simple letter jobs and I got buy with the old laptop.

I should have said it was the version of SigneBlazer that was posted that didn't list the cutter VM has it just won't connect to it. Yes it's the full version and I got it from UScutter

I loaded it on the tower computer and it doesn't have a driver listed for my cutter, so for right now I'll have to put up with the nag screen on the laptop. I don't want to change something that's working till I get Vinyl Master up and running. I'm hoping that adaptor you showed will work and then it's off to the races

Yep, the nag screen bugs me but if it works, for now, that's what I got. I ordered the adaptor like MZ SKEETER suggested and will try that as soon as it shows up. I have tried every USB port and nothing I'm going to contact the makers of vinyl master and see if they have any idea

Might give that a try. l got VinylMaster loaded on the laptop and it doesn’t work I’m thinking that I wasted 500 bucks I can start signblazer and it works but VM won’t connect. I’ll try getting one of those adapters

Well no luck so far I deleted VM and re loaded it I tried the chip set link above and nothing. I tried SB on the tower machine and nothing. so now im trying to load VM on the laptop that works with signeblazer to see if that works. I think it is a problem with my tower machine more than a problem with the cutter. Its going to be some setting that is hiding some where

Vmaster pro has the driver in it I think

MZ SKEETER Didn't mean to not say hello to you just too many irons in the fire. Thanks for the links I'LL look at them tonight to see if anything in there will help

Hello Slice Yep it's been a while, Computer crash and life and all that. But now I'm trying to get back into the cutting thing. My old laptop is running SignBlazer UNcracked and the cutter works fine running XP, my home tower is running Windows 8.1 with VinylMaster pro is the one that's gunking up the works. In device manager under USB the port with the cutter has the yellow triangle if I hit the update driver button it says that the driver is up to date. I have lots of other USB devices that I plug in and out of this computer and they all work. And also my MH721 is an older MK1 not a MK2 if that makes a difference

This is driving me crazy. I am able to run SignBlazer on an old laptop and it cuts just fine but when I try to run it on my home computer that I have vinylmaster pro on I get "Windows has stopped this device because it has reported problems. (Code 43)" and "A request for the USB device descriptor failed" Vinylmaster pro it's self works fine it's just that windows won't recognize the USB and shuts it down for some reason. Any help would be much appreciated