alikat1109
Members-
Content Count
32 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Everything posted by alikat1109
-
What is the best vinyl to do on shirts. Thabks
-
And do u have a problem with it after its washed
-
I have a roll of vinyl that says SOLID on the back. I can't find this brand anywhere. Can someone help please. Thanks
-
Thank you everyone. I have a little (as you can see) of a certain color, that a customer wants, and I can't remember where I purchased it. Thanks again. This forum is great.
-
Good Morning, I'm trying to cut this picture out. Can anyone help. I only need the rocks w/o the letters. I use Sure cuts a lot pro 3 Thanks
-
Hello, I just put together my MH871, and I ran a test cut and (several times), and it's cutting through my image. How do I stop this? Thanks Allison
-
How do I cut an image multiple times on sure cuts a lot pro? I'm using MH871. I have a job and need to cut an image 100 times. Please help. Thanks
-
Hello Everyone, I need help. I have a sticker that i'm trying to cut. It's mulitple colors, and the center of the words are not cutting, also the performance at the bottom isn't cutting at all. What am I doing wrong? Also if someone can tell me how to paste a picture instead of uploading it on here that would be wonderful LOL. I'm using sure cuts with a mh871 PPPPPPPPPPPPPP.EPS
-
I did but shut down after. I will try again tomorrow. Thank u
-
I have PCUT 360 Using Signblazer. I have had this machine for 2 years, and it was cutting fine. All of sudden it now wont' close the cuts. Large, small letters, numbers. I have changed the blade, tightened the belt for the blade (which helped alittle). I've slowed down the cutter. I have unistalled the software and reinstalled. Not sure what I"m missing. Can someone please help. Thanks Allison
-
here it is. let me know if it shows up
-
PCut 630 for parts or repair
alikat1109 replied to myshally's topic in Creation PCUT Cutting Plotter Discussion
Would you be willing to part it out? I have the same one, but only need parts. Like the Vinyl roller, and new usb. -
Ok so I have adjusted it, and the cap has come closer to being closed, but the lines are getting closer (almost overlaping) on the number. so a fat 3 is now skinny with the lines almost overlapping. Some of the lines are also running further than they should. Any ideas?
-
That was awsome. I have wondered what the easiest way was. That just answered my question. Thanks
-
Where should the offset be? I have never had to change this before? How do I tell if the blade is spinning? I have check for debri in the holder! Sorry for these stupid questions. Thanks again.
-
MH365 not cutting completely through letters and curves.
alikat1109 replied to ekhatch's topic in SignBlazer
Hello everyone. Thanks for taking your time to read this. I'm using Signblazer Pcut 360. I'm trying to cut out a phone #, and no matter how big or little I cut it, its not connect from the begining to end. I have changed the offset, from anywhere from .00-.55. Could there be anything else I'm missing? I also have changed the cutting spead from 60 to 20. Still nothing has changed. The same spots everytime it cut it. Allison I did see someone say to tighten the belt. I did that and it made it better, but still not closing the cuts. PLEASE HELP. I have been using this cutter for about 2 years, and this is the first time I have come across this. I have change the blade.- 6 replies
-
- mh365
- notcutting
-
(and 1 more)
Tagged with:
-
Ok so i'm trying to copy the font above "sickies", but with Pats instead. I can't seem to get it right. I'm using Signblazer, and I can't get it. Can anyone please help. I'm not sure what I"m doing wrong. I have been working on this for 4 days. Thanks in advance. Allison
-
Thank you very much!!!!!
-
Would anyone be able to tell me what this font is?
-
I have an image that when I make it smaller part of the lines disappear. I also cuts that way. I would really appreciate anyone's help. Thanks Allison For some reason it won't allow me to attach the photos.
-
Image Sizing Issue
alikat1109 replied to alikat1109's topic in Creation PCUT Cutting Plotter Support Requests
I think I finally am able to do it!!!!!!