MarwanB

Members
  • Content Count

    21
  • Joined

  • Last visited

    Never

Everything posted by MarwanB

  1. MarwanB

    SB Not Responding!

    SB is very temperamental it stops responding when it feels like it. Sometimes it will work great for 5 to 6 cuts and then it stops working. Other times it stops from the begining. This happens when I send a job to the PCUT as soon as I press "Cut Tile". I am forced to restart the computer everytime it stops responding. Help please!
  2. My PCUT cuts Inconsistentley. i.e. I am cutting the words Valley Maid, see attached image, part of the letter "V" cuts too shallow, part cuts fine and part cuts too deep and goes through the paper. I highlighted the parts in yellow for some feedback. I tried to cut on the right side, left side and middle of the PCUT; it does the same thing. I experimented with blade depth, speed, blade offset, pressure, fonts to no avail. I checked alignment, cutting blade, cutting strip. It has been 2 weeks of frustration. This is brand NEW PCUT machine, 2 weeks old. Do I have a defective machine? Any help would be appreciated.
  3. The blade holder is in the back position and the blade spins freely 360 degrees. I read a lot of posts on this forum and I followed every tip I could find. It's the reason I purchased USCutter. It's great people like yourself that makes this forum. Any other ideas?
  4. MarwanB

    FREE VECTOR CLIP ART

    Great tip, can you post some links?
  5. My PCUT cuts deeper in the center of the project vs. the edges. i.e. "sssssssssssssss" the three middle ss are cut better then the outside ones. If I apply more pressure, the center of the vinyl will shred. Does that make sense? I cannot get my PCUT to cut evenly across the vinyl, why? Any help would be appriciated. Marwan
  6. Thank you, I wish such information were in the manual!
  7. MarwanB

    For Corel users

    Check-out this link: http://www.asigns.com/signtools_demo_g.htm
  8. MarwanB

    BLADE ADJUSTMENT

    Thanks Hobbot, mine is the same. Expert users recommend a hair-thin exposed blade! Nothing more than the thickness of the vinyl.
  9. MarwanB

    corel draw x3

    How do you add SignBlazer to the application luncher in Corel?
  10. MarwanB

    BLADE ADJUSTMENT

    Hobbot, How much of your blade is exposed?
  11. MarwanB

    IMPORTING FROM COREL

    How do you add SignBlazer to the application luncher in Corel?
  12. I inspected the blade holder carefully, there is no way to adjust the depth of the blade on this type of holder. It is basically drop-in type and screw-on the cover. There is no adjustment knobs or screws. Can someone elaborate on this?
  13. MarwanB

    BLADE ADJUSTMENT

    Your logic makes alot of sense . After I inspected the blade holder carefully, there is no way to adjust the depth of the blade on this type of holder. It is basically drop-in type and screw-on the cover. There is no adjustment knobs or screws. Can someone elaborate on this?
  14. MarwanB

    How do I import vector art from corel 12 to signblazer

    Bruce, Do care to provide us with the steps?
  15. MarwanB

    corel driver

    I have CorelDraw 10 and SignBlazer. Can I set it up to do the same, no export? How do I set it up Marwan
  16. MarwanB

    BLADE ADJUSTMENT

    Hi Tater, Does this also applies to PCUT cutter? My blade sticks out about a quarter of an inch. Marwan
  17. Thank you BannerJhon, I checked with straight edge ruler. The cutting strip is straight flat. Do you have other advises? Marwan
  18. Hi, I received my USCutter yesterday. It worked fine last night. Today it's shredding the vinyl!!!! Marwan
  19. I used black vinyl and it blends well. Some odd design; you think the manufacture would had figured it out. Marwan
  20. It was the front lip! I will try the masking tape. Thanks, Marwan
  21. MarwanB

    New and in Trouble

    Hi, I received my USCutter yesterday. It worked fine last night. Today it's shredding the vinyl!!!! Marwan