Nikolay

Yesterday i had to make new windows instalattion on new hard drive. I deactivated the license and activated it on the new hardware. Installed all programs from the CD i got with the plotter. Now 80% of my files .fs ( graphtec pro studio files ) are not opening. Its or program instantly crashes, or just opening white blank without any objects. Tried to update software, version 4.0 , version 3,8 , nothing helped.

this dots appears about a week after placement. Vinyl is from " Stahls "

I use 45' blade cant make it to cut all the way to the corner. Corners are unfinished and cant peal small details. Problem 1 RED : Not reaching the corners. Problem 2 GREEN : sometimes lines are not fully cutrted. Have uncutted spaces.

it is 90 microns and veeeeeerry elastic. Name : Sports FIlm I have 150 microns , 0 elastic Name : Subli stop and 80 microns 0 elastic. Name : Premium Plus Problem is same for every Vinyl, uncutted corners.

Is there ony settings tat i have to change when using different blades, ( except force and speed, i know i have to change them for different media and different blades )

I will try now to cut Text

lines are cutted perfectly at 13, so there is enoughh force. But corners are bad. in 14 is the same. in 15 comes the good corners, but the lines are already+2 force and deep in waxpaper.

Yes settings are 100 % the same, it is easy for me to use PC for settings. It is good, Just the blade goes deep in waxpapaer to have this perfect result. .. and will wear out faster.

Force 15 Amazingly good....... Thank you !!!!! IMG_3015.MOV

A bit more blade, Force 10 no cut , force 13 good lines, and Uncut corners. IMG_3013.MOV

force 22, same result but holder start dragging the vinyl. i dont think i can put more force. Next step is to pull out the blade a bit ? 0-02-0a-36f253d4db8d9cb8b6617779b0dc6dc4992d0f988af78c53cd3b76fc47dfffa0_cef814a0.mp4

Force 20 with less blade IMG_3010.MOV

I dont know what is this 0.1 on the display it appears after i change the acceleration from 2 to 1 and start adjusting the force and speed. It was not there when i reset deffault settings.

i have done it. good lines and uncut corners Just did a reset to default settings. And made it with your way again but same result. Uncut corners i changed the blade with new one, same... uncut corners plotter is Brand new from the shop.

With or without lens , i tryed to fully hide the blade, then little pullout and test with different force. then pull a bit more and test again with forces, and again and again. Perfect condition was 10 force with 5 speed. All lines of my Text are perfect , Just corners are Uncut. When go over this 10 force, knife go deeper in wax, but corners remains uncut.

I have the lens for adjusting the blade. It is set to the first line. I tested fine adjusting it to + or - lenght, not better results in cornesrs. so far the best for streight lines is with force 10 but corners still remain uncut perfectly. with force 11-12-13 same results , just blade go deeper in waxpaper. 10 is perfect with verry little scratch on paper. perfect lines, but Uncut corners. Offset +1 +2/ -1 -2 no result in corners. Speed up and down - no result for corners. Changed the blade with 30' and 60' - no result for corners. Do i Have to adjust the Offset Angle ? Or some other settings to full cut this corners.

What ? I am cutting the vinyl ofcorse, but when peeling off it is leaving some strange traces of glue arround the cuts and it is hard to pull the vinyl. The matte and the transperant parts are both the waxpaper, both are with glue, But on the transperant part it is verry hard to pull the vinyl up.

Hello, New problem on the horizon Black part of Vinyl is cutted good and smooth, But the sticky part is verry bad, verry hard to pull on places arround the cuts . But if the stiky part is clear, it is verry easy to pull up. Anybody know what is the problem ?

Maybe this 2 lanes on the lens do not mean 2mm, becouse i berelly feel it on my finger. and it is not 2mm at all... it is less then 1mm.. maybe it is my mistake to call it 2mm...

i will check this, it makes sense. just long job is cutting now. have to wait it.

When i do this, blade holder is dragging heavilly into the vinyl, will make video soon.

200 words - perfect.