Worble7
Members-
Content Count
90 -
Joined
-
Last visited
-
Days Won
3
Content Type
Profiles
Forums
Gallery
Everything posted by Worble7
-
Hello Everyone, Yes I have read and adjusted my cutting blade right as long as there no position you need to set the blade in carrer and the holder I just drop it in and tighten. So my problem is when I weed my project the vinyl does not come off clean there a snap at the last spot coming off the backing. So I put a brand new blade in thinking that blade was worn. same thing and ever worse as it;s not cutting right. see pic please. Also my setting are on simple mode outdoor vinyl the force is defalt at 12 and the plus is set at 0. Thanks Jeff
-
Alignment marks as to line up multiple vinyl
Worble7 posted a topic in GraphTec Cutting Plotter Discussion
Hello, I did marks like the one in the photo so I can line up my vinyl. Now I can't figure out how i put them there I have looked everywhere but one place I guess? Is it in inkscape or graphtec pro studio. Thanks for the help. Jeff -
Alignment marks as to line up multiple vinyl
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Thanks Wildgoose and everyone that help -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Thanks MZ SKEETER I see wow that's way differnt. Some of it is still in the software on mine. -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Thanks Darcshadow -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
I'm using graphtec PRo studio.....So you use the setting in there for force/offset/and all that? -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Thanks I'm located in California so should be here fast. Here's my last cut on normal mode and the vinyl is cut all the way through on this one no pulling with a stuck tab of vinyl. In set up area I don't see offset on mine. Do the settings stay after you powder down the unit? Thanks Jeff -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Thanks Blue tip holder also -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Thanks I will go look for there site and buy 5 maybe 10 at this rate lol do you have a link and does your take the same blade?? Thanks -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Also What blades do you use MZ SKEETER? -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Ok I will read and get into normal mode and show my cuts then. Thanks -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
I'm in simple mode I think I should be in normal mode. I will let you know after I read and get in normal mode. Thanks for the help -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
MZ SKEETER, Should I do my setting elsewhere? -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
That's where I set my force and speed in simple mode. -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
-
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
So Will the backing paper break off the blade tip as I never went through the paper? Also are there better blades? I did take the blade holder out again and tested it and your right it was too long not by much. Here are my new cuts and it still has a tab sticking not a clean cut the triangle cuts clean I circled the area that is not all the way cut. Thanks -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
So Will the backing paper break off the blade tip as I never went through the paper? Also are there better blades? I did take the blade holder out again and tested it and your right it was too long not by much. Here are my new cuts and it still has a tab sticking not a clean cut the triangle cuts clean I circled the area that is not all the way cut. Thanks -
Cutting Problem Graphtec CE6000-60
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
MZ SKEETER, It's A brand new blade I know it looks way wrong nothing smothe about it. Here's a pic of the settings I have and the blade I'm using. Thanks Jeff -
Alignment marks as to line up multiple vinyl
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
I went back and downloaded ver. 2.90 has the reg marks put them in and it worked great. Now why would they change this is my question?? Thanks everyone for your help. Jeff -
Alignment marks as to line up multiple vinyl
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
I know it's something simple I'm missing but I can't put my finger on it......This is what the cut screen looks like after I did both colors and still not showing up in cut. I have 4 windows as where i think I should have 2 correct? I come and tinker every few days so I don't lose my mind. Thanks Jeff -
Alignment marks as to line up multiple vinyl
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Yes I did.....this does not turn on and off my colors like she can also a differnt program but I usderstand they all work kind of the same. Here's a screen shot -
Alignment marks as to line up multiple vinyl
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Mike, I'm not getting it ugh I will be steping away from the computer before I smash it lol i will take a break and come back later. Thanks for your help. Jeff -
Alignment marks as to line up multiple vinyl
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Ok I'm missing the copy part where do I copy it from the cut/plot area?? -
Alignment marks as to line up multiple vinyl
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Also when should I put the marks/shape in to the image? I did it after I used inkscape to vectorize it. Jeff -
Alignment marks as to line up multiple vinyl
Worble7 replied to Worble7's topic in GraphTec Cutting Plotter Discussion
Mike, when you say copy the marks where do I copy them from?