SC Series Vinyl Cutter Discussions

161 topics in this forum

1. Set Up Problem

   By AndreaJohnson, January 5
   • 4 replies
   • 84 views
   • 
   • slice&dice
   • January 6

2. Slow down speed lower than 100mm/sec?

   By Zeppelin1007, December 5, 2019
   • 8 replies
   • 107 views
   • 
   • Wildgoose
   • December 6, 2019

3. SC2 Advancing vinyl too far

   By srbbrandt, December 1, 2019   

   • sc2
   • vinyl
   • (and 1 more)

     Tagged with:

     • sc2
     • vinyl
     • advancing
   • 5 replies
   • 110 views
   • 
   • MZ SKEETER
   • December 5, 2019

4. SC Cuttng Software

   By vezman71, November 24, 2019
   • 4 replies
   • 121 views
   • 
   • slice&dice
   • November 26, 2019

5. pinch roller purchase ?

   By TT57, October 31, 2019
   • 4 replies
   • 156 views
   • 
   • MZ SKEETER
   • November 1, 2019

6. Cutting Mat/6mil acetate

   By tracienvegas, October 17, 2019
   • 3 replies
   • 173 views
   • 
   • tracienvegas
   • October 18, 2019

7. SC2 Bunching vinyl Help!

   By melissa826, September 25, 2019
   • 4 replies
   • 185 views
   • 
   • Wildgoose
   • September 29, 2019

8. Now is cutting message

   By hawksview, September 13, 2019
   • 5 replies
   • 128 views
   • 
   • hawksview
   • September 16, 2019

9. Cutting at the beginning

   By Heathw, September 12, 2019
   • 5 replies
   • 138 views
   • 
   • Dakotagrafx
   • September 12, 2019

10. Vinyl tracking

    By daddycreswell, August 23, 2019
    • 18 replies
    • 333 views
    • 
    • daddycreswell
    • August 26, 2019

11. SC series sudden blade depth cutting issue?

    By CraftySoul6, August 5, 2019
    • 2 replies
    • 151 views
    • 
    • haumana
    • August 5, 2019

12. 1st Gen SC and SCAL 5 Pro

    By Celerity Photography, July 9, 2019
    • 15 replies
    • 348 views
    • 
    • Wildgoose
    • July 16, 2019

13. SC2 Problems going from USB to Serial

    By G3 Design, July 7, 2019
    • 18 replies
    • 342 views
    • 
    • MZ SKEETER
    • July 7, 2019

14. Blade Carriage Moves to Right and Doesn't Stop

    By Trevinous, May 3, 2014   

    • moves to right
    • broken
    • (and 1 more)

      Tagged with:

      • moves to right
      • broken
      • blade carriage
    • 5 replies
    • 1,938 views
    • 
    • zombrolio
    • June 6, 2019

15. USCutter SC2 ARM and Contour cutting not aligning properly

    By vofur, May 27, 2019
    • 3 replies
    • 377 views
    • 
    • MZ SKEETER
    • May 27, 2019

16. How Do you install the belt? Is there a video?

    By April51, April 14, 2019   

    • broken belt
    • belt relacement
    • (and 4 more)

      Tagged with:

      • broken belt
      • belt relacement
      • video
      • install belt
      • help
      • how do you
    • 20 replies
    • 621 views
    • 
    • Dakotagrafx
    • May 2, 2019

17. Hooked up SC and cannot cut or find port

    By point blank design, March 8, 2019
    • 6 replies
    • 424 views
    • 
    • point blank design
    • April 11, 2019

18. Connect to Mac? USB? Not found!

    • 1
    • 2
    • 3
    • 4

    By SicSkinz, September 29, 2018
    • 82 replies
    • 3,493 views
    • 
    • darcshadow
    • March 12, 2019

19. Contour Cutting Issues

    By erock, March 10, 2019
    • 15 replies
    • 339 views
    • 
    • MZ SKEETER
    • March 10, 2019

20. Plugged My SC2 into USB. It blew up.

    By Zeppelin1007, March 10, 2019
    • 4 replies
    • 269 views
    • 
    • Zeppelin1007
    • March 10, 2019

21. 28" vs 34" sc2 cutter

    By Raptor77racer, November 23, 2018
    • 9 replies
    • 783 views
    • 
    • Stenn
    • February 19, 2019

22. Jimmy

    By jholli3098@att.net, July 11, 2018
    • 21 replies
    • 828 views
    • 
    • darcshadow
    • February 19, 2019

23. SC2 has arrived -- Has a Problem

    By slice&dice, March 22, 2018
    • 14 replies
    • 1,204 views
    • 
    • Stenn
    • February 19, 2019

24. Win10 drivers for SC 631e

    • 1
    • 2

    By VicT, January 20, 2019
    • 31 replies
    • 1,175 views
    • 
    • VicT
    • January 22, 2019

25. SC2 34" left side not cutting

    By Cwnosky, December 28, 2018
    • 7 replies
    • 381 views
    • 
    • Wildgoose
    • January 22, 2019