Clamshell Heat Press Discussion or Support

177 topics in this forum

1. Temperature Converasion table

   By firemalt, December 7, 2008
   • 14 replies
   • 11,093 views
   • 
   • Kenla
   • March 20, 2012

2. How to get support

   By BannerJohn, July 21, 2009
   • 0 replies
   • 5,023 views
   • 
   • BannerJohn
   • July 21, 2009

3. WARNING!!!

   By BannerJohn, December 7, 2008
   • 0 replies
   • 6,496 views
   • 
   • BannerJohn
   • December 7, 2008

4. Heat Press Won't Heat Past 80 Degrees

   By wdutrieuille, January 13, 2019
   • 8 replies
   • 1,073 views
   • 
   • Dakotagrafx
   • January 13, 2019

5. My clamshell heat press pops open!!

   By Dekrahl, December 3, 2018
   • 9 replies
   • 779 views
   • 
   • darcshadow
   • January 3, 2019

6. Heat press Issues and bad support

   By KristiB, November 24, 2018
   • 3 replies
   • 588 views
   • 
   • Go-C Graphics
   • November 27, 2018

7. Hix HT 400 how to use dials for temp

   By Staciestitches, October 13, 2018
   • 3 replies
   • 745 views
   • 
   • Staciestitches
   • October 14, 2018

8. Foam Pad - Disregard, found the answer below.

   By Kurt, July 12, 2018
   • 0 replies
   • 658 views
   • 
   • Kurt
   • July 12, 2018

9. Platen cover?

   By StayHungryFL, May 26, 2018
   • 6 replies
   • 485 views
   • 
   • Dakotagrafx
   • May 26, 2018

10. Hat Heat Pres

    By VinylNewbie, March 10, 2018
    • 2 replies
    • 1,002 views
    • 
    • bobinlasvegas
    • April 17, 2018

11. second press of medium is not sticking to the first adhesion press, and heat press is sticking where i cannot open it if i set it as required and not staying down if i set it for less force

    By TOY, February 7, 2018   

    • heat press handle will not realse
    • too much press not enough press
    • 0 replies
    • 521 views
    • 
    • TOY
    • February 7, 2018

12. HEAT PRESS TEMP HELP. (I HAVE THE RED US CUTTER CLAMSHELL MODEL HP 3802)

    By cloading, September 1, 2016
    • 11 replies
    • 2,002 views
    • 
    • Dakotagrafx
    • January 15, 2018

13. us cutter 15 x 15 clamshell heat press model 3802

    By bobinlasvegas, January 15, 2018   

    • heat press
    • 10 replies
    • 780 views
    • 
    • Dakotagrafx
    • January 15, 2018

14. Cheapest and best place to buy Thermoflex, especially for starter pack?

    By Chudimac, January 2, 2018   

    • thermoflex
    • cheap
    • (and 2 more)

      Tagged with:

      • thermoflex
      • cheap
      • affordable
      • where to buy
    • 8 replies
    • 1,359 views
    • 
    • cardudenc
    • January 3, 2018

15. what's the purpose of calibrating- no change

    By cuddlebug studio, October 28, 2017
    • 1 reply
    • 1,138 views
    • 
    • Dakotagrafx
    • October 28, 2017

16. Temperature problems

    By Drpatterson, July 29, 2017   

    • 15x15 clamshell heat press
    • 5 replies
    • 2,106 views
    • 
    • Wildgoose
    • July 29, 2017

17. New 3802 with Temperature problems

    By Mags, July 17, 2017   

    • 3802
    • temperature
    • 5 replies
    • 1,236 views
    • 
    • Mags
    • July 18, 2017

18. New heat press help

    By Jhamelton, November 19, 2016   

    • heat press
    • pad
    • 10 replies
    • 2,328 views
    • 
    • Wildgoose
    • March 16, 2017

19. Melting Baseball Cap Mesh

    By Jacunivac, December 26, 2016   

    • heat press
    • baseball caps
    • (and 1 more)

      Tagged with:

      • heat press
      • baseball caps
      • melting plastic
    • 1 reply
    • 1,194 views
    • 
    • mfatty500
    • December 26, 2016

20. Just getting started

    By Craftyginger, November 3, 2016
    • 3 replies
    • 1,109 views
    • 
    • Jay2703
    • November 4, 2016

21. 16x20 Perfect Press Auto Open - Not Heating Up

    By iamtherookie, April 9, 2016
    • 11 replies
    • 2,536 views
    • 
    • MadHatterGraphix
    • April 15, 2016

22. http://www.uscutter.com/USCutter-Perfect-Press-15-x-15-Clamshell-Auto-Open-Heat-Press

    By maxcat128, February 11, 2016
    • 0 replies
    • 1,152 views
    • 
    • maxcat128
    • February 11, 2016

23. ....Old STAHLS heat transfer press information needed...

    By signmaker, May 5, 2015
    • 0 replies
    • 1,519 views
    • 
    • signmaker
    • May 5, 2015

24. What do you think of this one?

    By outlaws, April 18, 2014
    • 16 replies
    • 2,185 views
    • 
    • outlaws
    • May 14, 2014

25. a little help

    By livinloudgraphics, January 25, 2014
    • 2 replies
    • 1,408 views
    • 
    • Wildgoose
    • January 26, 2014