GraphTec Cutting Plotter Support Requests

337 topics in this forum

1. Factory Reset

   By signpro, March 25, 2009
   • 18 replies
   • 46,488 views
   • 
   • MZ SKEETER
   • December 27, 2020

2. How to get support

   By BannerJohn, July 21, 2009
   • 0 replies
   • 9,154 views
   • 
   • BannerJohn
   • July 21, 2009

3. Graphtec C6000-40Plus not communicating

   By TEES ON U, September 9
   • 10 replies
   • 111 views
   • 
   • TEES ON U
   • Sunday at 08:37 PM

4. Design Position Way Off

   By webcat, September 10
   • 12 replies
   • 89 views
   • 
   • MZ SKEETER
   • September 11

5. Graphtec ce6000-40 plus...connection not found

   By AkeeLaMor, March 15, 2020
   • 2 replies
   • 614 views
   • 
   • TEES ON U
   • September 8

6. Cutting X+ Direction Uneven - CE7000-60

   • 1
   • 2

   By levy4u, July 23
   • 33 replies
   • 624 views
   • 
   • Dakotagrafx
   • August 27

7. How to enter the LOADER Menu?

   By aguilar, August 19
   • 0 replies
   • 48 views
   • 
   • aguilar
   • August 19

8. Can't read registration mark white 2 designs on media

   By MarcusSuriname, July 24
   • 0 replies
   • 66 views
   • 
   • MarcusSuriname
   • July 24

9. CE7000 Curves not cutting properly - choppy

   • 1
   • 2

   By NTBVinyls, June 17
   • 25 replies
   • 367 views
   • 
   • MZ SKEETER
   • July 8

10. Text not showing on CM3

    By Bridport Graphics, June 22
    • 1 reply
    • 91 views
    • 
    • Dakotagrafx
    • June 22

11. CE3000-60 mk2 help

    By Rebel2256, June 8
    • 6 replies
    • 233 views
    • 
    • Rebel2256
    • June 20

12. ce lite 50 Graphtec Vinyl Cutting Pro, can I hire you?

    By AudienceByStorm, June 12   

    • graphtec ce lite
    • graphtec
    • 3 replies
    • 164 views
    • 
    • slice&dice
    • June 13

13. Cut through on the Graphtec CE6000-60?

    By YerrytheYanitor, June 10
    • 2 replies
    • 116 views
    • 
    • darcshadow
    • June 10

14. Fix for common CE5000 issues!

    By Tomblarom, May 20   

    • brick
    • firmware
    • (and 3 more)

      Tagged with:

      • brick
      • firmware
      • loader
      • start boot error
      • mac
    • 1 reply
    • 135 views
    • 
    • haumana
    • May 21

15. graphtec 60 v3 90hl

    By HOMESTEADSTENCIL, July 21, 2017
    • 19 replies
    • 1,773 views
    • 
    • naitch
    • May 20

16. Graphtec FC8600 Contour Cut Alignment Issues

    By dtdm, July 20, 2015
    • 15 replies
    • 11,979 views
    • 
    • MZ SKEETER
    • May 14

17. Graphtec ce7000 Contour Cut Alignment Issues

    By Graphtec-CE50-LITE, May 13
    • 0 replies
    • 99 views
    • 
    • Graphtec-CE50-LITE
    • May 13

18. Graphtec ce6000-60 plus

    • 1
    • 2
    • 3

    By DawnR, May 7
    • 61 replies
    • 830 views
    • 
    • DawnR
    • May 11

19. Graphtec CE7000 loses accuracy on contour cut near rollers

    • 1
    • 2
    • 3

    By annarface, April 28
    • 50 replies
    • 1,181 views
    • 
    • MZ SKEETER
    • May 9

20. Graphtec cutting plotter controller

    By Dewi, April 11
    • 7 replies
    • 239 views
    • 
    • MZ SKEETER
    • April 17

21. Cutting issue CE6000

    By A_Pola, October 1, 2017
    • 18 replies
    • 2,920 views
    • 
    • haumana
    • April 7

22. CE2000-60

    By Mike Berry, April 3
    • 1 reply
    • 151 views
    • 
    • Wildgoose
    • April 4

23. CE7000 Double cutting

    By Hawaii Kai, March 30
    • 8 replies
    • 277 views
    • 
    • Wildgoose
    • April 4

24. graphtec pro studio

    By ynot333, March 16
    • 18 replies
    • 511 views
    • 
    • bikemike
    • March 18

25. ce7000 not cutting some nodes

    By lilone2j, March 11   

    • graphtec studio
    • 10 replies
    • 215 views
    • 
    • lilone2j
    • March 18