GraphTec Cutting Plotter Discussion

General discussion pertaining to the GraphTec cutting plotters. (Please do not post support requests here)

484 topics in this forum

  1. Graphtec ce7000-60 bowing issue on 24 media

    By puchacho,
    • 1 reply
    • 582 views

  2. stencil material slides out of place

    By Spotted Dog,
    • 1 reply
    • 522 views

  3. Problems w Graphtec Very choppy, horrible cuts :(

    By twocents,
    • 19 replies
    • 7,107 views

  4. Removal of pinch roller

    By Anetski,
    • 12 replies
    • 2,032 views

  5. Graphtec 8600 Cutting Jagged Lost Settings

    By Capt'n Morgan,
    • 0 replies
    • 457 views

  6. Having a Scale issue !

    By Josh mason,   
    • 3 replies
    • 911 views

  7. Graphtec CE6000-40 Sensor Offset Adj

    By LouLouNovice,
    • 0 replies
    • 559 views

  8. Settings seem off

    By 3 Kells Design,
    • 10 replies
    • 1,120 views

  9. Cutting out off line

    By Dee's T's & More,   
    • 1 reply
    • 530 views

  10. Plotter Controller

    By Pradeep,
    • 1 reply
    • 573 views

  11. New-to-me Graphtec CE6000-40 Plus

    By Rojhan,
    • 1 reply
    • 785 views

  12. GRAPHTECH CE6000-120 AP

    By Tony chamu,
    • 12 replies
    • 1,926 views

  13. CE5000-60 load media prompt

    By mikeguam,
    • 15 replies
    • 5,515 views

  14. GRAPHTEC CE6000-60 NOT WORKING

    By JOSE GARCIA,
    • 2 replies
    • 1,438 views

  15. CE6000-40 adding random cut lines

    By AbsoluteInk,
    • 1 reply
    • 506 views

  16. Graphtec ce6000-60 vinyl rollers

    By Grandpa,
    • 7 replies
    • 865 views

  17. Ce6000-60 Plus RANDOM Extra Cut Lines or diagonal scribbles all over job

    By New Creations By Jen,   
    • 23 replies
    • 1,724 views

  18. Brand new CE7000-60 starts, cuts a 1cm line then moves 2cm and starts to cut job

    By Kembs,
    • 9 replies
    • 827 views

  19. Cutmaster 4 job setup question..

    By keith20mm,
    • 0 replies
    • 558 views

  20. CE6000-60 Not Reading Registration Marks

    By MerchForFans,
    • 1 reply
    • 1,057 views

  21. FC8000 Y belt maintenance?

    By EverythingVinyl,
    • 0 replies
    • 579 views

  22. Graphtec FC9000 Cutter Issue (May not be be issue with the cutter)

    By Ddecals,
    • 1 reply
    • 665 views

  23. Software update

    By bikemike,
    • 9 replies
    • 892 views

  24. Graphtec ce7000 not finishing cuts.

    By Nellycuttz,
    • 13 replies
    • 1,641 views

  25. Its Been A Long Time Question Please

    By Capt'n Morgan,
    • 3 replies
    • 681 views