GraphTec Cutting Plotter Discussion

357 topics in this forum

1. CE 6000-60 vs the Titan 3 28 inch.

   By RedTacoDriver, January 29, 2016
   • 4 replies
   • 1,095 views
   • 
   • Primal Decals
   • August 6, 2016

2. CE5000-60 Looking for part

   By Carlos Sanunga, June 17, 2016
   • 6 replies
   • 990 views
   • 
   • MZ SKEETER
   • June 17, 2016

3. Is the CE5000-60 actually compatible with Windows 10?

   By socceronly, May 27, 2016
   • 3 replies
   • 1,128 views
   • 
   • socceronly
   • May 27, 2016

4. Recommended Blades for CE6000-60

   By wickedstangs, February 29, 2016   

   • Blades
   • 9 replies
   • 1,321 views
   • 
   • Jburns
   • May 20, 2016

5. Graphtec Ce5000-60 Freezes

   By gcextreme, March 1, 2016
   • 20 replies
   • 1,383 views
   • 
   • darcshadow
   • May 17, 2016

6. IS THIS CAUSED FROM A DULL BLADE?

   By The Elvis Legacy, April 21, 2016
   • 8 replies
   • 931 views
   • 
   • mr300s
   • April 22, 2016

7. How to set Default Conditions?

   By ign 5, April 14, 2016   

   • fc7000-100 default changes
   • 3 replies
   • 751 views
   • 
   • ign 5
   • April 17, 2016

8. Cutting 22" wide on a 24" roll? (new Graphtec user)

   By Dorese, April 11, 2016   

   • Graphtec
   • Setup help
   • 4 replies
   • 659 views
   • 
   • MZ SKEETER
   • April 11, 2016

9. Graptec varying results

   By marduk, April 2, 2016
   • 24 replies
   • 1,273 views
   • 
   • bikemike
   • April 5, 2016

10. Graphtec 6000 motherboard change

    By Appleuser, June 25, 2015
    • 9 replies
    • 1,218 views
    • 
    • SMW
    • March 23, 2016

11. Graphtec FC5100 750

    By Signscreative, March 19, 2016
    • 1 reply
    • 411 views
    • 
    • mb20music
    • March 19, 2016

12. CE6000-60 Vacuum Hold Down?

    By Camel, March 10, 2016
    • 18 replies
    • 1,252 views
    • 
    • mfatty500
    • March 12, 2016

13. Help, FC7000 only cutting half page

    By ign 5, March 7, 2016
    • 12 replies
    • 1,051 views
    • 
    • MZ SKEETER
    • March 9, 2016

14. How can I stop my Graphtec cutter from lifting on every line segment?

    • 1
    • 2

    By bigmark1972, February 23, 2016
    • 28 replies
    • 1,493 views
    • 
    • Wildgoose
    • February 25, 2016

15. Graphtec help needed

    By xpaperman, December 10, 2015
    • 19 replies
    • 1,291 views
    • 
    • jaybyrd
    • February 18, 2016

16. Graphtec CE5000-60 Weed frame alignment issues

    By kimmy123, January 23, 2016
    • 0 replies
    • 444 views
    • 
    • kimmy123
    • January 23, 2016

17. FC8600 not cutting small stuff properly

    • 1
    • 2

    By TimEdwards888, December 9, 2015
    • 40 replies
    • 3,602 views
    • 
    • TimEdwards888
    • December 15, 2015

18. Thinking about buying from Alibaba - do fakes exist?

    By Trillion, December 7, 2015
    • 11 replies
    • 811 views
    • 
    • Trillion
    • December 11, 2015

19. Best plotter cutter for absolute detail work? (less than 5mm characters)

    By Jonesy, November 26, 2015
    • 17 replies
    • 1,622 views
    • 
    • Jonesy
    • November 27, 2015

20. CE6000-60

    By Signs and Designs, November 14, 2015
    • 3 replies
    • 642 views
    • 
    • Dakotagrafx
    • November 14, 2015

21. Contour Cutting with my Ce5000

    By gcextreme, October 9, 2015
    • 14 replies
    • 888 views
    • 
    • MadHatterGraphix
    • October 27, 2015

22. Graphtec JX1130 SignJet Pro 54

    By MadHatterGraphix, October 23, 2015
    • 8 replies
    • 1,565 views
    • 
    • MadHatterGraphix
    • October 24, 2015

23. Graphtec fc4100-130 cutting project from vinyl spool

    By jcsocal, October 14, 2015
    • 5 replies
    • 630 views
    • 
    • jcsocal
    • October 14, 2015

24. What Maintenance to do CE5000

    By Izzy11, October 10, 2015
    • 11 replies
    • 1,594 views
    • 
    • Dakotagrafx
    • October 14, 2015

25. Graphtec

    By jdmarti1, September 30, 2015
    • 11 replies
    • 897 views
    • 
    • djque
    • October 4, 2015