GraphTec Cutting Plotter Discussion

484 topics in this forum

1. Graphtec Plotter Controller use

   By Carmigirl, September 6, 2016
   • 0 replies
   • 909 views
   • 
   • Carmigirl
   • September 6, 2016

2. GraphTec ce-6000-40 will not cut chrome?

   By DeonCarpenter, August 31, 2016
   • 4 replies
   • 1,278 views
   • 
   • FrznFire07
   • September 2, 2016

3. what am I doing wrong

   By bethann, August 31, 2016
   • 6 replies
   • 1,304 views
   • 
   • bethann
   • September 1, 2016

4. graphtec ce5000-60 Making Stencils

   By JeremyH, August 19, 2016
   • 3 replies
   • 2,737 views
   • 
   • PatrickR
   • August 20, 2016

5. Graphtec flash nv error

   By Leway, August 9, 2016
   • 5 replies
   • 1,896 views
   • 
   • mb20music
   • August 10, 2016

6. CE 6000-60 vs the Titan 3 28 inch.

   By RedTacoDriver, January 29, 2016
   • 4 replies
   • 2,258 views
   • 
   • Primal Decals
   • August 6, 2016

7. CE5000-60 Looking for part

   By Carlos Sanunga, June 17, 2016
   • 6 replies
   • 2,023 views
   • 
   • MZ SKEETER
   • June 17, 2016

8. Is the CE5000-60 actually compatible with Windows 10?

   By socceronly, May 27, 2016
   • 3 replies
   • 2,748 views
   • 
   • socceronly
   • May 27, 2016

9. Recommended Blades for CE6000-60

   By wickedstangs, February 29, 2016   

   • Blades
   • 9 replies
   • 2,492 views
   • 
   • Jburns
   • May 20, 2016

10. Graphtec Ce5000-60 Freezes

    By gcextreme, March 1, 2016
    • 20 replies
    • 3,672 views
    • 
    • darcshadow
    • May 17, 2016

11. IS THIS CAUSED FROM A DULL BLADE?

    By The Elvis Legacy, April 21, 2016
    • 8 replies
    • 2,024 views
    • 
    • mr300s
    • April 22, 2016

12. How to set Default Conditions?

    By ign 5, April 14, 2016   

    • fc7000-100 default changes
    • 3 replies
    • 1,606 views
    • 
    • ign 5
    • April 17, 2016

13. Cutting 22" wide on a 24" roll? (new Graphtec user)

    By Dorese, April 11, 2016   

    • Graphtec
    • Setup help
    • 4 replies
    • 1,126 views
    • 
    • MZ SKEETER
    • April 11, 2016

14. Graptec varying results

    By marduk, April 2, 2016
    • 24 replies
    • 2,358 views
    • 
    • bikemike
    • April 5, 2016

15. Graphtec 6000 motherboard change

    By Appleuser, June 25, 2015
    • 9 replies
    • 2,142 views
    • 
    • SMW
    • March 23, 2016

16. Graphtec FC5100 750

    By Signscreative, March 19, 2016
    • 1 reply
    • 856 views
    • 
    • mb20music
    • March 19, 2016

17. CE6000-60 Vacuum Hold Down?

    By Camel, March 10, 2016
    • 18 replies
    • 2,625 views
    • 
    • mfatty500
    • March 12, 2016

18. Help, FC7000 only cutting half page

    By ign 5, March 7, 2016
    • 12 replies
    • 3,390 views
    • 
    • MZ SKEETER
    • March 9, 2016

19. How can I stop my Graphtec cutter from lifting on every line segment?

    • 1
    • 2

    By bigmark1972, February 23, 2016
    • 28 replies
    • 3,525 views
    • 
    • Wildgoose
    • February 25, 2016

20. Graphtec help needed

    By xpaperman, December 10, 2015
    • 19 replies
    • 2,472 views
    • 
    • jaybyrd
    • February 18, 2016

21. Graphtec CE5000-60 Weed frame alignment issues

    By kimmy123, January 23, 2016
    • 0 replies
    • 930 views
    • 
    • kimmy123
    • January 23, 2016

22. FC8600 not cutting small stuff properly

    • 1
    • 2

    By TimEdwards888, December 9, 2015
    • 40 replies
    • 7,386 views
    • 
    • TimEdwards888
    • December 15, 2015

23. Thinking about buying from Alibaba - do fakes exist?

    By Trillion, December 7, 2015
    • 11 replies
    • 1,658 views
    • 
    • Trillion
    • December 11, 2015

24. Best plotter cutter for absolute detail work? (less than 5mm characters)

    By Jonesy, November 26, 2015
    • 17 replies
    • 5,021 views
    • 
    • Jonesy
    • November 27, 2015

25. CE6000-60

    By Signs and Designs, November 14, 2015
    • 3 replies
    • 1,106 views
    • 
    • Dakotagrafx
    • November 14, 2015