GraphTec Cutting Plotter Discussion

General discussion pertaining to the GraphTec cutting plotters. (Please do not post support requests here)

484 topics in this forum

  1. Craft Robo Info

    By BannerJohn,
    • 5 replies
    • 11,363 views

  2. info from graphtec for cutmaster 3 and Graphtec studio

    By Dakotagrafx,
    • 4 replies
    • 5,049 views

  3. Graphtec CE-7000 with a combo Machine labeler

    By James159,
    • 0 replies
    • 187 views

  4. ce7000-60 8.5 x 11 max. working area

    By Daryl,
    • 5 replies
    • 458 views

  5. Cutting Master 5 not cutting outer edges

    By UO-Jeremy,   
    • 10 replies
    • 737 views

  6. Graphtec FC9000 Take Up System

    By JustCut,
    • 0 replies
    • 211 views

  7. Can we contour cut outside of registration marks?

    By kcherdch,
    • 1 reply
    • 371 views

  8. Cutting Master 5 Contour cutting is not supported for multi-page design

    By UO-Jeremy,   
    • 11 replies
    • 1,241 views

  9. FC8600-Cut Master 4 issue

    By jeffdpia,   
    • 3 replies
    • 615 views

  10. Graphtec 6000-40 Plus: stopped die cutting, blades dulling fast

    By Spam on Maui,
    • 8 replies
    • 820 views

  11. Graphtec F-Mark 1 suckers: looking for the old style

    By Spam on Maui,
    • 7 replies
    • 719 views

  12. CrossCut Not Cutting Entire Width

    By westman,   
    • 1 reply
    • 677 views

  13. Graphtec FC8600 cant hold calibration

    By Bigfoot Graphix,
    • 4 replies
    • 1,110 views

  14. ARMS - Sense level was not enough

    By LSpe,
    • 1 reply
    • 915 views

  15. fc8600 not cutting in the right position

    By Bigfoot Graphix,
    • 1 reply
    • 553 views

  16. CE-6000 Push Roller - Ease to Slide

    By darcshadow,
    • 1 reply
    • 423 views

  17. Graphtec CE7000 Push Rollers

    By ECombs,
    • 99 replies
    • 11,429 views

  18. FC8600 How to cut without registration marks.

    By Chaos & Co,
    • 5 replies
    • 873 views

  19. [FC8600-75] Nearly impossible to draw on center of sheet

    By Professor Bauman,
    • 6 replies
    • 1,063 views

  20. Newbie Graphtec CE5000-60 Owner Questions

    By Doug Beck,
    • 6 replies
    • 983 views

  21. graphtec ce 6000-40 plus telecamera

    By andrea73,
    • 2 replies
    • 944 views

  22. Start and finish points does not align

    By winslo93,
    • 11 replies
    • 1,645 views

  23. Graphtec CE700-60 issie

    By Brothers,
    • 0 replies
    • 650 views

  24. FC 8600-75 Not retracting cross cut and tries to cross cut with cut blade

    By mistwist,
    • 8 replies
    • 1,682 views

  25. Any suggestions best place to sell our FC5100-75 and FC2240-120ES cutters

    By DTCAZ,
    • 2 replies
    • 831 views