USCutter Refine Cutting Plotter Discussion

793 topics in this forum

1. MH 721 has issues with small letters, and offset only makes it worse!!!!

   By moss2029, March 8, 2013
   • 7 replies
   • 1,841 views
   • 
   • Dakotagrafx
   • March 22, 2013

2. MH-721 blade settings

   By egobuster1, February 11, 2013
   • 0 replies
   • 1,081 views
   • 
   • egobuster1
   • February 11, 2013

3. MH-721 Started getting really Loud

   By rally864, February 6, 2013
   • 0 replies
   • 585 views
   • 
   • rally864
   • February 6, 2013

4. MH-871 not turning on?

   By mountaindr3wz, January 28, 2013
   • 10 replies
   • 2,073 views
   • 
   • Dakotagrafx
   • February 3, 2013

5. MH721 Set-Up on Mac - Driver Software? - Detecting and Installing Cutter

   By TEXASS, July 5, 2010
   • 6 replies
   • 13,596 views
   • 
   • jon521
   • January 17, 2013

6. MH-365

   By gpau, January 8, 2013
   • 0 replies
   • 487 views
   • 
   • gpau
   • January 8, 2013

7. contour cutting without a laser light

   By daimagic, January 1, 2013
   • 4 replies
   • 757 views
   • 
   • aguilar
   • January 5, 2013

8. Switching from USB to Serial-USB connection on MH721, getting error

   By blackpaws, January 3, 2013
   • 9 replies
   • 2,662 views
   • 
   • slice&dice
   • January 4, 2013

9. Can an MH-871 cut magnet sheets?

   By JHew84, December 9, 2012
   • 7 replies
   • 3,273 views
   • 
   • JHew84
   • December 17, 2012

10. Changed to serial, can't get SC to work now.

    By imaseahawksfan, October 16, 2012
    • 8 replies
    • 1,300 views
    • 
    • Monkey
    • December 8, 2012

11. MH871 won't cut...then hits red button on side.

    By Squewheet, November 16, 2012
    • 6 replies
    • 1,336 views
    • 
    • Squewheet
    • November 21, 2012

12. Serial port Cable?

    By randyb, November 16, 2012
    • 2 replies
    • 784 views
    • 
    • randyb
    • November 16, 2012

13. I hate to make another thread, but...

    By Rob@MM, November 1, 2012
    • 5 replies
    • 743 views
    • 
    • vinylmotivations
    • November 2, 2012

14. MH 721-MK2 Cutting Problems

    By bigrapidstrophies, October 9, 2012   

    • Not Responding
    • Never-ending Lines
    • 1 reply
    • 2,622 views
    • 
    • Jay2703
    • October 9, 2012

15. Cutting Strip on MH721

    By xJoey Dubsx, October 12, 2010
    • 5 replies
    • 2,437 views
    • 
    • Fred Kaz
    • September 30, 2012

16. MH 871 Problems

    By sluggo2u, June 16, 2012
    • 5 replies
    • 3,935 views
    • 
    • Pcrat
    • September 22, 2012

17. refine 28" drivers

    By philstubbs, September 4, 2012
    • 5 replies
    • 1,165 views
    • 
    • philstubbs
    • September 13, 2012

18. I love my MH 871, never a problem, just need new blades after a year...

    By T3rry, September 1, 2012
    • 5 replies
    • 1,073 views
    • 
    • MZ SKEETER
    • September 1, 2012

19. Y axis freaking out!!!

    By highonlif, August 23, 2012
    • 8 replies
    • 1,376 views
    • 
    • Jay2703
    • August 24, 2012

20. mh721 cutting through design

    By egobuster1, July 11, 2012
    • 9 replies
    • 1,684 views
    • 
    • Dr12volt1338
    • August 21, 2012

21. MH 721 Won't cut 90 degree angles cleanly

    By GuerillaGraphics, June 22, 2012
    • 4 replies
    • 1,244 views
    • 
    • highonlif
    • August 9, 2012

22. Refine MH721

    By bagmania01, August 5, 2012   

    • Refine Mh721
    • setup
    • 2 replies
    • 1,626 views
    • 
    • Jay2703
    • August 6, 2012

23. You guessed it, Mh 721 cutting problems..

    By ecto1, June 21, 2012
    • 9 replies
    • 4,037 views
    • 
    • slice&dice
    • July 27, 2012

24. mh1351 not cutting proper

    By crow11, May 24, 2011
    • 2 replies
    • 1,606 views
    • 
    • Mikelemazo
    • July 21, 2012

25. USB> Serial vs Installing Serial ports in PC

    By tweetlbug, July 11, 2012
    • 7 replies
    • 1,598 views
    • 
    • tweetlbug
    • July 12, 2012